| Device Properties |
| Property name |
Property type |
Description |
| HM_LargeDownStep |
Tango::DEV_LONG |
The large step to move the mirror down in Half Mode (unit = um |
| HM_Delay |
Tango::DEV_LONG |
Delay between each control loop in Half Mode (unit = mS |
| HM_LowestPos |
Tango::DEV_LONG |
Lowest Mirror position in half mode (unit = um |
| HM_LowerLimitTemp |
Tango::DEV_DOUBLE |
Lower Temperature limit in Half Mode (unit = deg celcius |
| HM_UpperLimitTemp |
Tango::DEV_DOUBLE |
Upper limit temperature in Half Mode (unit = deg celcius |
| HM_FaultTemp |
Tango::DEV_DOUBLE |
Temperature threshold to switch the mirror to fault (unit = deg celcius |
| HM_StepUp |
Tango::DEV_LONG |
Step (up) size in Half Mode (unit = um |
| HM_StepDown |
Tango::DEV_LONG |
Step (down) size in Half Mode (unit = um |
| SM_BeamCenter |
Tango::DEV_LONG |
Theoritical beam center position (unit = um |
| SM_MinTemp |
Tango::DEV_DOUBLE |
Temperature threshold to start the mirror position control (unit = deg celcius |
| SM_HystTemp |
Tango::DEV_DOUBLE |
Temperature hysteresis in Slotted Mode (unit = deg celcius |
| SM_Step |
Tango::DEV_LONG |
Step size in Slotted Mode (unit = um |
| SM_Delay |
Tango::DEV_SHORT |
Control loop delay in Slotted mode (unit = mS |
| SM_FollowRange |
Tango::DEV_LONG |
Threashold to switch the mirror in FAULT in Slotted Mode (unit = um |
| T1_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T1 measurement |
| T2_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T2 measurement |
| T3_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T3 measurement |
| T4_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T4 measurement |
| T5_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T5 measurement |
| T6_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T6 measurement |
| T7_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T7 measurement |
| T8_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T8 measurement |
| T9_CorrFactor |
Tango::DEV_DOUBLE |
Correction factor for T9 measurement |
| Incoherency_low |
Tango::DEV_DOUBLE |
Low value for temperature incoherency |
| Incoherency_high |
Tango::DEV_DOUBLE |
High value for temperature incoherency |
| SR_CurrentLimit |
Tango::DEV_DOUBLE |
Storage ring current limit to move the mirror through the beam in Slotted
Mode (unit = mA |
| SR_CurrentDevName |
Tango::DEV_STRING |
Storage ring beam current device name |
| HM_SmallDownStep |
Tango::DEV_LONG |
The small step to move the mirror down in Half Mode (unit = um |
| HM_InterlockTemp |
Tango::DEV_DOUBLE |
Temperarute hard-wired interlock in half mode |
| SM_UpperInterlockTemp |
Tango::DEV_DOUBLE |
Upper temperature hard-wired interlock in slotted mode |
| SM_LowerInterlockTemp |
Tango::DEV_DOUBLE |
Lower temperature hard wired interlock in slotted mode |
| DHDBDevName |
Tango::DEV_STRING |
Tango HDB DHDB device name |
| SR_CheckCurrent |
Tango::DEV_STRING |
Check if there is some beam in SR. Should be "yes" or "no" |
| HDB_enabled |
Tango::DEV_STRING |
Set to "yes" to send value history in HDB when an error is detected |
| Mirror_mode |
Tango::DEV_STRING |
Mode of the mirror.
This property corresponds to the command which is executed when
the Insert command is called.
Possible values are (case insensitive) HalfMode or SlottedMode.
|
